Siemens SIMOTION P320-4 E Commissioning And Hardware Installation Manual Download

Page: 112 / 222

When installing the indoor bus cable, you should also remember the following boundary

conditions (d

= outer diameter of the cable):

Table 6-2

Boundary conditions for indoor routing of bus cable

Features

General conditions

Bending radius for a single bend

≥ 80 mm (10 × d

)

Bend radius for multiple bends

≥160 mm (20 × d

)

Permissible temperature range for installation

- 5° C to + 50° C

Temperature range for storage and stationary op‐

eration

- 30° C to + 65° C

Note
The length codes for the pre-assembled cables can be found on the website

www.siemens.com/simotion (

www.siemens.com/simotion

6.6

Connecting Ethernet

Procedure

Plug the LAN cable into the Ethernet interface of the SIMOTION P320‑4. You must hear the

connection engage properly.

Cables

Standard shielded twisted pair cables are used for the networking in this case.
The following connection cables are recommended:
● SIMATIC NET, ind. Ethernet TP XP CORD RJ45/RJ45, TP CORD assembled with 2 RJ45

connectors, send and receive cables crossed (cross-over)

Order no.: 6XV1850-2H*)

● SIMATIC NET, ind. Ethernet TP CORD RJ45/RJ45, TP CORD assembled with 2 RJ45

connectors

Order no.: 6XV1850-2G*)

*) Length code

Dimensions

E50

0.5 m

H10

1 m

H20

2 m

H60

6 m

N10

10 m

Connection
6.6 Connecting Ethernet

SIMOTION P320-4 E / P320-4 S

112

Commissioning and Hardware Installation Manual, 11/2016

Summary of Contents for SIMOTION P320-4 E































































































































































































































Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands

Siemens SIMOTION P320-4 E, Commissioning And Hardware Installation Manual

Search results

Summary of Contents for SIMOTION P320-4 E

Reviews:

Related manuals for SIMOTION P320-4 E

Brands by name

Popular brands