Siemens SIMOTICS M-1PH818 Operating And Installation Instructions Download

Page: 93 / 314

7.6

Set values for monitoring the bearing temperature (optional)

Prior to commissioning

If the machine is equipped with bearing thermometers, set the temperature value for

disconnection on the monitoring equipment before the first machine run.

Table 7-2

Set values for monitoring the bearing temperatures before commissioning

Set value

Temperature

Alarm

115 °C

Shutting down

120 °C

Normal operation

Measure the normal operating temperature of the bearings T

at the installation location in

°C. Set the values for shutdown and warning corresponding to the operating temperature T

Table 7-3

Set values for monitoring the bearing temperatures

Set value

Temperature

Alarm

operation

+ 5 K ≤ 115 °C

Shutting down

operation

+ 10 K ≤ 120 °C

Commissioning

7.6 Set values for monitoring the bearing temperature (optional)

SIMOTICS M-1PH8 1PH818., 1PH822., 1PH828.

Operating Instructions 10/2017

Summary of Contents for SIMOTICS M-1PH818



























































































































































































































































































































Search results

Summary of Contents for SIMOTICS M-1PH818

Reviews:

Related manuals for SIMOTICS M-1PH818

Brands by name

Popular brands

Siemens SIMOTICS M-1PH818, Operating And Installation Instructions

Search results

Summary of Contents for SIMOTICS M-1PH818

Reviews:

Related manuals for SIMOTICS M-1PH818

Brands by name

Popular brands