Siemens SIMOTICS M-1PH818 Operating And Installation Instructions Download

Page: 83 / 314

Figure 6-8

Sensor Module

①

mounted on the terminal box

NOTICE
Modifying the cable outlet direction
Changing the cable outlet direction by any improper means will damage the connecting

cables.
The permissible rotation range must not be exceeded. A maximum of ten changes to the

rotation angle of the Sensor Module are permissible within the rotation range.

6.3.4

Connect the holding brake

Information for electrically connecting the holding brake can be found in the operating

instructions supplied by the manufacturer in the (Page 169) appendix.

6.3.5

Connecting the temperature sensor

● The temperature sensor is connected to the signal connector together with the speed

encoder signal.

● For the version without speed encoder, the temperature sensor is connected at the terminal

strip.

● The motor has a reserve temperature sensor, which is also connected at the auxiliary

terminal strip. Reconnect the temperature sensor as needed, e.g. if the previous

temperature sensor fails.

Electrical connection

6.3 Auxiliary circuits

SIMOTICS M-1PH8 1PH818., 1PH822., 1PH828.

Operating Instructions 10/2017

Summary of Contents for SIMOTICS M-1PH818



























































































































































































































































































































Search results

Summary of Contents for SIMOTICS M-1PH818

Reviews:

Related manuals for SIMOTICS M-1PH818

Brands by name

Popular brands

Siemens SIMOTICS M-1PH818, Operating And Installation Instructions

Search results

Summary of Contents for SIMOTICS M-1PH818

Reviews:

Related manuals for SIMOTICS M-1PH818

Brands by name

Popular brands