Siemens SIMOTICS M-1PH818 Operating And Installation Instructions Download | Manualshive

Page: 49 / 314

background image

Mounting

5

When carrying out any work on the machine, observe the general safety instructions

(Page 15) and the specifications contained in EN 50110‑1 regarding safe operation of electrical

equipment.

Note
Loss of conformity with European directives
In the delivery state, the machine corresponds to the requirements of the European directives.

Unauthorized changes or modifications to the machine lead to the loss of conformity with

European directives and the loss of warranty.

5.1

Preparing for installation

5.1.1

Requirements for installation

The following requirements must be satisfied prior to starting installation work:
● Staff have access to the operating and installation instructions.
● The machine is unpacked and ready for mounting at the installation location.

Note
Measure the insulation resistance of the winding before starting installation work
Wherever possible, measure the insulation resistance of the winding before starting

installation work. If the insulation resistance lies below the specified value, take appropriate

remedial measures. These remedial measures may necessitate the machine being

removed again and transported.

NOTICE
High temperatures
The motor components get very hot during operation. High temperatures can damage

mounting parts such as the cable insulation.
● Temperature-sensitive parts such as normal cables or electronic components must not

rest against or be attached to mounted machine parts.

● Only use heat-resistant mounting parts. The connecting cables and cable entries must be

suitable for the ambient temperature.

SIMOTICS M-1PH8 1PH818., 1PH822., 1PH828.

Operating Instructions 10/2017

49

«
...
47
48
49
50
51
...
»

Summary of Contents for SIMOTICS M-1PH818



























































































































































































































































































































Reviews:

No comments

Related manuals for SIMOTICS M-1PH818

Brand: Sachs Pages: 75

Plug & Play Plus

Brand: CHERUBINI Pages: 16

Brand: Stuart Turner Pages: 20

Brand: Baratza Pages: 5

Johnson BJ25E4SUC

Brand: BRP Pages: 265

Brand: Briggs & Stratton Pages: 6

Low Voltage Motors EQPIII-841

Brand: Toshiba Pages: 2

Low Voltage Motors VR Series

Brand: Toshiba Pages: 2

Brand: Toshiba Pages: 18

Brand: Toshiba Pages: 31

Brand: Toshiba Pages: 49

Brand: Hatz Diesel Pages: 63

Brand: SSANGYONG Pages: 16

Brand: SSANGYONG Pages: 42

Brand: Toro Pages: 96

Brand: Canaline Engines Pages: 39

Brand: Yanmar Pages: 394

Brand: ARO Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands