Siemens SIMOTICS M-1PH818 Operating And Installation Instructions Download | Manualshive

Page: 26 / 314

background image

Supplementary devices

A temperature sensor is integrated in the stator winding to monitor the winding temperature.

The type of temperature sensor is specified on the rating plate.
Depending on the order options, various supplementary devices such as encoder systems can

be either installed or mounted.

Holding brake

Depending on the order, a special version of a holding brake from the Stromag company is

mounted. Various types of holding brake are mounted depending on the shaft height.

NOTICE
Technical data for the special version of the holding brake
The following technical data applies to the special version of the mounted holding brake. The

corresponding data in the manufacturers operating instructions do not apply.

Table 3-3

Technical data of the holding brake

Technical data

NFF-A 63

AH180

NFF-A 100

AH225

Braking torque

M

Brake

[Nm]

1000

1600

Max. speed

n

Brake

[rpm]

3500

3100

Weight incl. hollow shaft

m

brake

[kg]

63

88

Moment of inertia

J

brake

[kgm

2

]

0,022

0,051

Total moment of inertia (emer‐

gency stop)

J

total

[kgm

2

]

1,3

3,9

Rated voltage

U

[V]

230 V (AC)

230 V (AC)

Permitted single switched energy P

[W]

98

210

Coil current

I

[A]

2,21

2,70

Number of emergency stops

Z

-

2100

1200

Opening time

[ms]

300

300

Closing time

[ms]

80

100

Note
More information
● Commissioning (Page 87)

See also

Operating instructions, holding brake (Page 169)

Description

SIMOTICS M-1PH8 1PH818., 1PH822., 1PH828.

26

Operating Instructions 10/2017

«
...
24
25
26
27
28
...
»

Summary of Contents for SIMOTICS M-1PH818



























































































































































































































































































































Reviews:

No comments

Related manuals for SIMOTICS M-1PH818

Brand: Kohler Pages: 108

CentriPro Xtreme Duty Series

Brand: Xylem Pages: 12

General Pump 103166

Brand: Interpump Group Pages: 3

Brand: Volkswagen Pages: 64

Brand: SICK Pages: 20

Brand: Ingersoll-Rand Pages: 127

Brand: Toyota Pages: 599

Brand: LinMot Pages: 26

Brand: Honda Pages: 133

Brand: MVVS Pages: 6

AQUACRAFT .18 MARINE

Brand: Hobbico Pages: 4

Brand: Vetus Pages: 134

Brand: HRW Pages: 23

Brand: Nice Pages: 12

Brand: Hama Pages: 15

Brand: Daytona Pages: 37

DSR ADVENTURE 125

Brand: um Pages: 120

Brand: Parker Pages: 107

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands