Siemens SIMOTICS M-1PH818 Page 123 Operating And Installation Instructions Download | Manualshive

Page: 123 / 314

background image

Assembly

● Push the protecting ring over the end of the shaft.
● For 1PH818. or 1PH822. motors, ensure that the outer collar is placed with a space of 1 mm

from the bearing end shield (detail Z).

ཱ

=

PP

=

Figure 9-3

Fitting the protecting ring

9.3.6

Removing and mounting the bearing shields

1. Unscrew the belt pulleys. The belt pulleys may be jammed or distorted, in which case you

should lever them off carefully.

2. Remove the bearing shield.

– When removing the bearing shields, take care that the windings are not damaged.
– For water-cooled motors, also ensure that the cooling water pipes are not damaged.

For assembly, proceed in reverse order.

WARNING

Lifting using the cooling water pipes
The cooling water pipe system has not been designed so that it can be used to lift the motor.

The machine can fall when lifted. Death, serious injury, or material damage will result.
● Only use the eyebolts on the bearing shields to transport and lift the motor.

9.3.7

Installing and sealing the motor

Strictly ensure the greatest possible care and cleanliness when repairing the machine.

Maintenance

9.3 Repair

SIMOTICS M-1PH8 1PH818., 1PH822., 1PH828.

Operating Instructions 10/2017

123

«
...
121
122
123
124
125
...
»

Summary of Contents for SIMOTICS M-1PH818



























































































































































































































































































































Reviews:

No comments

Related manuals for SIMOTICS M-1PH818

Brand: BONFIGLIOLI Pages: 36

Brand: Stobag Pages: 40

Brand: Festo Pages: 76

Sonesse Ultra 50 DC RS485

Brand: SOMFY Pages: 16

Brand: Zundapp Pages: 52

90000 I/C 525 Series

Brand: Briggs & Stratton Pages: 16

Quantum Jazzy 1400

Brand: Pride Mobility Pages: 2

Brand: Price Industries Limited Pages: 17

Brand: Volvo Pages: 20

Brand: Volvo Pages: 51

Brand: Volvo Pages: 76

Brand: Detroit Diesel Pages: 39

Brand: Detroit Diesel Pages: 122

Brand: Detroit Diesel Pages: 121

Brand: Chevrolet Pages: 130

Ultra Drive UN-99

Brand: Bettcher Pages: 29

Brand: LONCIN Pages: 57

Brand: STEYR Pages: 331

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands