Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 151

Page: 151 / 188

Install the V ring

1. Grease the axial sealing surface. The shaft seating remains ungreased.

①

V ring

②

Mounting aid washer

③

Protective ring

Figure 9-3

Install the V ring

2. Push the V ring

①

onto the shaft using an assembly disk

②

The V ring is in the correct axial position when the face surface is flush with the outer edge

of the V ring.

Install the protective ring for IP56 degree of protection

For degree of protection IP56, the V ring for the outer bearing seal is fitted with a sheet steel

protective ring

③

in the bearing cover.

1. Push the protective ring onto the shaft.
2. Verify that the ring is sufficiently pretensioned. Replace the protective ring, if necessary.
3. Position the protective ring so that one of the longitudinal grooves meets the corresponding

water separation groove at the bottom in the bearing cover flange or end shield.

9.2.3.6

Installing the V ring ("Increased degree of protection" option)

The grease chamber of the labyrinth sealing ring together with the V ring ensures compliance

with degree of protection IP65.

Maintenance

9.2 Corrective Maintenance

SIMOTICS FD 1MH1

Operating Instructions 08/2017

151

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands

Siemens SIMOTICS FD 1LL1, Operating Instructions & Installation Instructions

Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands