Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 134

Page: 134 / 188

9.1

Inspection and maintenance

9.1.1

Safety instructions for inspection and maintenance

WARNING

Rotating and live parts
Electric machines contain live and rotating parts. Fatal or serious injuries and substantial

material damage can occur if maintenance work is performed on the machine when it is not

stopped or not de-energized.
● Perform maintenance work on the machine only when it is stopped. The only operation

permissible while the machine is rotating is regreasing the roller bearings.

● When performing maintenance work, comply with the five safety rules (Page 16).

WARNING

Machine damage
If the machine is not maintained it can suffer damage. This can cause faults which can result

in eventual or immediate death, serious injury or material damage.
Perform regular maintenance on the machine.

CAUTION

Dust disturbances when working with compressed air
When cleaning with compressed air, dust, metal chips, or cleaning agents can be whirled up.

Injuries can result.
When cleaning using compressed air, make sure you use suitable extraction equipment and

wear protective equipment (safety goggles, protective suit, etc.).

NOTICE
Damage to insulation
If metal swarf enters the winding head when cleaning with compressed air, this can damage

the insulation. Clearance and creepage distances can be undershot. This may cause damage

to the machine extending to total failure.
When cleaning with compressed air, ensure there is adequate extraction.

Maintenance
9.1 Inspection and maintenance

SIMOTICS FD 1MH1

134

Operating Instructions 08/2017

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands

Siemens SIMOTICS FD 1LL1, Operating Instructions & Installation Instructions

Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands