Siemens SIMOCODE 3UF Programming And Operating Manual Download

Page: 139 / 172

SIMOCODE PRO V PN FDI
Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

139

Analog Value Recording

16.1

Analog Value Recording - Settings

Recording is carried out directly in SIMOCODE pro on the basis of the motor feeder and

independently of PROFINET or the automation system. Every analog value present at the

"allocated analog value" analog socket is recorded and saved. The recording starts on the

basis of the edge (positive/negative) via any binary signal at the Trigger Input of the function

block. Up to 60 values can be saved internally in the device.
The time frame of the recording is indirectly determined by the selected sampling rate:

Sampling time = sampling rate [s] x 60 values.
The Pre-trigger can be used to specify how far in advance the recording should commence

before the trigger signal is issued. The Pre-trigger is set as a percentage of the entire

sampling time.

Settings:

Signal/Value

Range

Trigger-Eingang

Analog value recording starts when any signal is issued

(arbitrary sockets , e.g. device inputs, motor current

flowing).

Allocated analog value

Any value (1 word/2 byte) in SIMOCODE pro

Trigger edge

positive / negative

Sampling rate

0.1 to 50 s in 0.1-s-increments

Pre-trigger

0 to 100 % in 5-%-increments

Summary of Contents for SIMOCODE 3UF













































































































































































Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands

Siemens SIMOCODE 3UF, Programming And Operating Manual

Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands