Siemens Simatic VS 710 Quick Reference Manual Download Page 30

Page: 30 / 38

SIMATIC VS710

Quick Reference Guide

SIMATIC VS 710

A5E00032597-02

Technical Specifications

This table contains the complete technical specifications for the VS 710.

5.1

General Specifications

Characteristic

Technical Specifications

VS 710

Order Number

SIMATIC VS 710:

6GF 1710-3AA

SIMATIC VS 710 (OEM): 6GF 1710-2AA

Dimensions

65 x 80 x 130 mm (W x H x D) with no mounting
bracket attached

Weight

Approx. 0.750 kg (without lens)

Interfaces
to S7/M7/C7
to PC

RS485 (12 Mbps)
RS232 (115 Kbps)

Power Supply

Supply voltage (V

)

Input voltage
protected
against polarity
reversal

Voltage
interruption
(can be
jumpered)

24 VDC; (20.4 to 28.8 VDC, safety extra low voltage,
SELV). The VS 710 has no integrated protection
against high-energy surge pulses in the

s range (surge

pulse). See EMC for external measures.

Yes

≥

20 ms

Current
consumption (I

)

I=480 mA (typ)/600 mA (max.)

Starting current

max. 10 A; 1 ms

Summary of Contents for Simatic VS 710







































Search results

Summary of Contents for Simatic VS 710

Reviews:

Related manuals for Simatic VS 710

Brands by name

Popular brands

Siemens Simatic VS 710, Quick Reference Manual

Search results

Summary of Contents for Simatic VS 710

Reviews:

Related manuals for Simatic VS 710

Brands by name

Popular brands