Siemens SIMATIC TDC System Manual Download

Page: 90 / 228

CPU modules

4.2 CPU module CPU550/CPU551

SIMATIC TDC hardware

System Manual, 08/2017, A5E01114865-AL

4.2.3

Control and display elements

LED display

The processor number, states and faults are displayed using a 5x7 dot matrix LED array.

Acknowledge button S1

This button has two functions:

●

Clearing the fault display:
The acknowledge button can be used to clear sporadic or non-critical fault displays on the

5x7 dot matrix LED. An additional fault is displayed after the first one has been

acknowledged.

●

Digital signal input can be evaluated using the ASI function block.

Front panel

Figure 4-3

Front panel of CPU551

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands