Siemens SIMATIC TDC System Manual Download Page 33

Page: 33 / 228

Installation and EMC guidelines

1.16 Cables

SIMATIC TDC hardware
System Manual, 08/2017, A5E01114865-AL

Design and temperature resistance

All cables must be made of copper and be able to resist temperatures of up to at least 90 °C.

Connection via interface module

If interface modules are used, the shields of system-side cables and of routed the interface

module to SIMATIC TDC must be bonded to ground directly above or below the interface

module. Unshielded conductors that are terminated to screw terminals should be kept as

short as possible.
All lines should be kept as short as possible.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands