Siemens SIMATIC TDC System Manual Download

Page: 200 / 228

Interface module

7.4 Interface module SB70

SIMATIC TDC hardware

200

System Manual, 08/2017, A5E01114865-AL

7.4.2

Application notes

The interface module is suitable for vertical and horizontal mounting positions

Other information

For more information on EMC and environmental conditions, refer to section "General

technical specifications (Page 37)"!
The following figure shows a typical application:

Figure 7-9

Application example of an SB70 interface module on digital I/O module SM500

The digital inputs of the interface module are connected via cable SC62 to the SIMATIC TDC

outputs.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands