Siemens SIMATIC TDC System Manual Download

Page: 184 / 228

Interface module

7.2 Interface module SB60

SIMATIC TDC hardware

184

System Manual, 08/2017, A5E01114865-AL

7.2.1

Signals

Signals up to a maximum of 120 V (nominal value) DC or AC can be connected at the SB60

interface module.

Yellow LED

The status of the binary interface module outputs (binary inputs for SIMATIC TDC) is

indicated using yellow LEDs (1...8).
Terminal block X2 provides two screw terminals for each signal:

●

terminals 12, 22, ... up to 82 for binary signals 120 V

●

terminals 11, 21, ... up to 81 for the reference point

Note
When wiring the signal lines to the terminals, observe “Installation and EMC Directives” in

the User Manual.

7.2.2

Application notes

The interface module is designed only for vertical mounting positions due to thermal losses

to be dissipated.

Other information

For more information on EMC and environmental conditions, refer to section "General

technical specifications (Page 37)"!

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands