Siemens SIMATIC TDC System Manual Download Page 18

Page: 18 / 228

Installation and EMC guidelines

1.9 Fire protection

SIMATIC TDC hardware

System Manual, 08/2017, A5E01114865-AL

1.9

Fire protection

As output power exceeds the limit of circuitry with power limiting to IEC 61010-1 /

IEC 61131-2, malfunction of a SIMATIC TDC component may pose the risk of fire according

to IEC 61010-1 / IEC 61131-2. In order to prevent spreading of fire, suitable measures must

be taken to prevent ignition of adjacent parts or components as a result of burning parts that

possibly drop out of a component.
Two examples of a fire protection barrier to IEC 61010-1

Example 1

Partition below the rack

Example 2

Metal panel
Accepted perforation of a metal panel

Minimum thickness [mm]

Maximum diameter of the holes

[mm]

Minimum hole pitch, center-center

[mm]

0.76

1.1

1.7 (35 holes/100 mm

)

0.76

1.2

2.4

0.89

1.9

3.2 (10 holes/100 mm

)

0.99

1.6

2.7

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands