Siemens SIMATIC TDC System Manual Download

Page: 177 / 228

Interface module

7.1 Interface module SB10

SIMATIC TDC hardware
System Manual, 08/2017, A5E01114865-AL

177

7.1.1

Signals

Yellow LED

The status of each of the 8 signals (1...8) is displayed by means of a yellow LED. Each

signal is provided a screw terminal on the two terminal blocks X2:

●

Terminals 1 to 8 for digital signals

●

Terminals 51 to 58 for reference points

Reference potential of the signals

The reference points of the signals may be derived from 1M or 1P potential. The polarity is

selected on the module by means of soldering bridge:

Figure 7-1

Soldering bridge for setting the signal reference points

Note
Bridge 1M-1W is inserted in the factory

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands