Siemens SIMATIC TDC System Manual Download Page 161

Page: 161 / 228

Communication modules

6.5 CP52A0 GDM access module

SIMATIC TDC hardware
System Manual, 08/2017, A5E01114865-AL

161

6.5.6

Connection options

Figure 6-14 Connection options of CP52A0

6.5.7

Additional components

Fiber-optic cable (FOC)

A fiber-optic cable with a

core diameter of 62.5 μm/125 μm

is used to interconnect the

CP52A0 GDM access module with the CP52IO GDM interface module. The cable is

connected by means of Duplex SC connectors.
The max. cable length for the connection between CP52IO and CP52A0 is 200 m.
The fiber-optic cables must be assembled in accordance with the plant topology and can be

ordered from the following supplier:
Ehret GmbH
Über der Elz 2
79312 Emmendingen

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands