Siemens SIMATIC RF120C Operating Instructions Manual Download

Page: 35 / 92

Parameter assignment and configuration

4.4 Ident instructions

Communications module RF120C with application blocks for S7-1200 and S7-1500
Operating Instructions, 07/2013, C79000-G8976-C328-01

Inserting the FBs in the program

The following elements must exist in the project to allow the function blocks to be compiled:

●

PLC data types

●

PLC tags

●

PIB_1200_UID_001KB

First copy this element from the library and insert it in your own program before you start to

select and program the function blocks.

4.4.1

Reset_Reader

With the "Reset_Reader" FB, all SIEMENS RFID reader types can be reset. All the readers

are reset to the settings stored in the device configuration of the RF120C. The

"Reset_Reader" FB has no specific parameters. The execution of the FB is started by the

"EXECUTE" parameter.
You will find descriptions of other Reset blocks for operation with the communications

modules RF180C and ASM 456 in the appendix of the operating instructions.

Figure 4-9

"Reset_Reader" function block

Summary of Contents for SIMATIC RF120C





























































































Search results

Summary of Contents for SIMATIC RF120C

Reviews:

Related manuals for SIMATIC RF120C

Brands by name

Popular brands

Siemens SIMATIC RF120C, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC RF120C

Reviews:

Related manuals for SIMATIC RF120C

Brands by name

Popular brands