Siemens SIMATIC PCS 7 SMART Page 17 Getting Started Download

Page: 17 / 210

Requirements for Getting Started

3.1

Hardware requirements for Getting Started - Part 1

Hardware components

The list below shows the hardware components you need for Getting Started. For some

hardware components, you must use a specific version because it is not possible to work on

Getting Started with an older version.

Hardware Component

Version Used in Getting Started

Other Version Possible

PG or PC with a standard

network card

Intel® PRO/1000

Yes

Rack

UR2

Yes

Power supply

PS 407 4A

Yes

CPU

CPU 410 SMART Firmware V8.2

Yes

Crossover cable

USB hardlock

PCS 7 SMART V9.0

No (Hardlocks are version

specific)

Use of other hardware components

If you are using other hardware components, you must place them in the relevant places. For

example, in HW Config, we recommend the usage of same components that are used in

Getting Started.
If you have different hardware, you can find additional information in the "

ES Configuration

Manual".

PCS 7 SMART Getting Started - Part 1 (V9.0 with APL)

Getting Started, 12/2017, A5E42181435-AA

Summary of Contents for SIMATIC PCS 7 SMART



















































































































































































































Search results

Summary of Contents for SIMATIC PCS 7 SMART

Reviews:

Related manuals for SIMATIC PCS 7 SMART

Brands by name

Popular brands

Siemens SIMATIC PCS 7 SMART, Getting Started

Search results

Summary of Contents for SIMATIC PCS 7 SMART

Reviews:

Related manuals for SIMATIC PCS 7 SMART

Brands by name

Popular brands