manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

Network structures 

 

6.1 WLAN 

 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 

214

 

Configuration Manual, 10/2015, C79000-G8976-C351-05 

Further notes 

You display the setting with the 

show wlan wds <wdsX 0/Y>

 command. 

See also 

wds partner mac (access point) (Page 214) 
wds partner wds-id (access point) (Page 215) 

6.1.7.2

 

wds partner mac (access point) 

Description    

With this command, you enter the MAC address of the WDS partner.  

 

 

Note 
This command is available only in access point mode. 

 

Requirement 

You are in the Interface Configuration mode for the WDS interface. 
The command prompt is as follows: 

cli (config-if-wdsX-0-Y)#

 

Syntax 

Call up the command with the following parameters: 

wds partner mac <mac-address>

 

The parameter has the following meaning: 

 

Parameters 

Description 

mac-address

 

MAC address of the communications partner 

Result  

The MAC address is specified. 

Further notes 

You display the setting with the 

show wlan wds <wdsX 0/Y>

 command. 

See also 

wds partner id-type (access point) (Page 213) 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Kathrein UHF-ANTENNEN OLYMPIA AOI 65 User Manual preview
UHF-ANTENNEN OLYMPIA AOI 65
Brand: Kathrein Pages: 12
PAR OMNIANGLE OA-144 Quick Start Manual preview
OMNIANGLE OA-144
Brand: PAR Pages: 4
C. Crane Super USB WiFi Antenna II Instruction Manual preview
Super USB WiFi Antenna II
Brand: C. Crane Pages: 16
ANTONICS OmPlecs TOP 200 AMR Installation Instruction preview
OmPlecs TOP 200 AMR
Brand: ANTONICS Pages: 2
Sea Tel 9711-44 KU-BAND TX/RX Installation And Operation Manual preview
9711-44 KU-BAND TX/RX
Brand: Sea Tel Pages: 256
Queclink OWNE User Manual preview
OWNE
Brand: Queclink Pages: 8
Nice AB Instructions For Fitting preview
AB
Brand: Nice Pages: 2
CreatComm TB8H User Manual preview
TB8H
Brand: CreatComm Pages: 36
CUSHCRAFT 15-4CD Skywalker Manual preview
15-4CD Skywalker
Brand: CUSHCRAFT Pages: 6
CommScope CMAX-D-43-UW-i53 Installation Manual preview
CMAX-D-43-UW-i53
Brand: CommScope Pages: 5
SteppIR 2E-3E High Wind Kit Manual preview
2E-3E High Wind Kit
Brand: SteppIR Pages: 13
King Controls 1500-HD Installation And Operating Instructions Manual preview
1500-HD
Brand: King Controls Pages: 40
Teltonika MAXVIEW MXL056 Installation & User'S Instructions preview
MAXVIEW MXL056
Brand: Teltonika Pages: 40
Benelec 02453 Installation Instructions Manual preview
02453
Brand: Benelec Pages: 6
cable matters 203003 User Manual preview
203003
Brand: cable matters Pages: 8
Accutech WI-ANT-P6 User Manual preview
WI-ANT-P6
Brand: Accutech Pages: 16
Edimax EA-OD14 Specifications preview
EA-OD14
Brand: Edimax Pages: 1
Edimax EA-OD19 Specifications preview
EA-OD19
Brand: Edimax Pages: 1

Brands by name

Popular brands

Load more brands