manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

 

Functions specific to SCALANCE 

 

4.5 Spectrum analyzer 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

109

 

4.5.2

 

WLAN Interface configuration mode 

This section describes commands that you can call up in the WLAN Interface Configuration 

mode. Depending on the Interface selected, various command sets are available.  
In the Global Configuration mode, enter the 

interface wlan 0/X

 command to change to this 

mode. 

●

 

If you exit the WLAN Interface Configuration mode with the 

exit

 command, you return to 

the Global Configuration mode. 

●

 

If you exit the WLAN Interface Configuration mode with the 

end

 command, you return to 

the Privileged EXEC mode. 

4.5.2.1

 

wlan spectrumanalyzer centerfrequency (Access Point) 

Description  

With this command you select the center frequency for measuring with the spectrum 

analyzer. 

 

 

Note 
This command is available only in access point mode. 

 

Requirement 

●

 

The WLAN interface is enabled. 

●

 

You are in the Interface Configuration mode of the WLAN interface. 
The command prompt is as follows:  

cli (config-if-wlan-0-X)#

 

Syntax 

Call up the command with the following parameters: 

wlan spectrumanalyzer centerfrequency { show-frequencies | frequency}

 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Crestron Antenna System SRD-ANT-1-PAK Installation Manual preview
Antenna System SRD-ANT-1-PAK
Brand: Crestron Pages: 16
Crest Audio SGA05329 Manual preview
SGA05329
Brand: Crest Audio Pages: 4
M2 Antenna Systems 215-470LP16 Manual preview
215-470LP16
Brand: M2 Antenna Systems Pages: 10
Labgear LAB350T User Manual preview
LAB350T
Brand: Labgear Pages: 2
RADIOHAUS SPIDERDXMAN RH-DX1020 Assembly Instructions Manual preview
SPIDERDXMAN RH-DX1020
Brand: RADIOHAUS Pages: 11
Sea Tel Base Exit Quick Start Manual preview
Base Exit
Brand: Sea Tel Pages: 10
Sea Tel 9707D-70 C-BAND TX Installation And Operation Manual preview
9707D-70 C-BAND TX
Brand: Sea Tel Pages: 83
M2 Antenna Systems 12M4DX Manual preview
12M4DX
Brand: M2 Antenna Systems Pages: 6
Cambium Networks PTP 820C Installation Manual preview
PTP 820C
Brand: Cambium Networks Pages: 206
Heath Tech Sidekick User Manual preview
Sidekick
Brand: Heath Tech Pages: 25
Etec E004ANT Instruction Manual preview
E004ANT
Brand: Etec Pages: 8
RedPort Aurora Iridium WiFi Terminal Installation And Setup Manual preview
Aurora Iridium WiFi Terminal
Brand: RedPort Pages: 8
Satellite AV GEOSATpro GS120 DiSEqC Manual preview
GEOSATpro GS120 DiSEqC
Brand: Satellite AV Pages: 10
Hughes Jupiter Pointing Manual preview
Jupiter
Brand: Hughes Pages: 47
Solid Signal YAGI Y5-2-6 Installation Instructions preview
YAGI Y5-2-6
Brand: Solid Signal Pages: 2
Mat-Tuner mAT-50 Instructions Manual preview
mAT-50
Brand: Mat-Tuner Pages: 6
Tarheel Antennas 40A-HP Instruction Manual preview
40A-HP
Brand: Tarheel Antennas Pages: 9
StarBand StarBand Satellite System Installation Manual preview
StarBand Satellite System
Brand: StarBand Pages: 38

Brands by name

Popular brands

Load more brands