background image

 

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722 

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com 

©2014 M2 Antenna Systems Incorporated 

 

01/14/14 

Rev.02 

Model  ........................................ 12M4DX 
Frequency Range ...................... 24.890 To 24.990 MHz 

*

Gain, (FS) / Over gnd ............... 10.7dBi / 16.4dBi @40’ 

Front to back .............................. 20 dB Typical 
Beamwidth   ............................... E=48° / H=58° 
Feed type ................................... Hair pin match 
Feed Impedance........................ 50 Ohms Unbalanced

 

Maximum VSWR ....................... 1.2:1 
Input Connector ......................... SO-239, Others avl. 

Power Handling ......................... 3 kW, Higher avl. 
Boom Length / Dia ..................... 27’ / 2” 
Element Length / Dia. ................ 21.25’ / 7/8” To 1/2” 
Turning Radius: ......................... 16’ 8” 
Stacking Distance ...................... 35’ To 41’ 
Mast Size ................................... 2” to 3 ” Nom. 
Wind area / Survival .................. 4.4 Sq. Ft. / 100 MPH 
Weight / Ship Wt. ....................... 28 Lbs. / 39 Lbs. 
 

M2 Antenna Systems, Inc. 

Model No: 12M4DX 

FEATURES: 

 

The 12M4DX is a great performer for its size. It was designed for low wind area but rugged and lightweight and it 

will save you a bundle on shipping. IT’S UPSABLE! like all our “DX” series. The computer optimized design allows full 
band coverage with good gain and front to back. Performance is excellent on both the CW and phone. Mechanically, 
CNC machined aluminum (6061-T6) ring clamps ground the elements to the boom and make assembly a snap. A hairpin 
type match couples the 3 kW 1: balun to the feed line. The antenna is completely DC grounded. The 12M4DX is also 
great for stacking, providing 3 dB increased gain not to mention the lower angle of radiation. The 12M4DX is a perfect 
stacking partner for our other “DX series Yagis like the 20M4DX and 10M4DX. Put the 12M4DX to the test in the new cy-
cle! 

SPECIFICATIONS: 

*Subtract 2.14 from dBi for dBd /  FS = Free Space 

 

 

Summary of Contents for 12M4DX







Reviews: