manualshive.com logo in svg

Siemens SIMATIC NET SCALANCE XCM-300, Product Manual

Share
Download
Siemens SIMATIC NET SCALANCE XCM-300 Product Manual Download Page 39

5.6

Wall mounting

Preparation

Note the position of the securing bar, see also section “Dimension drawings (Page 67)“.

When supplied, the securing bar is in the wall mounting position. You do not need to prepare the 
device any further.

If the securing bar is in the rail mounting position, note the section “Changing the position of the 
securing bar (Page 40)“.

Tools

To mount the device on a wall, you require the following:

• 2 wall plugs

• 2 fillister head screws

Note

Depending on the mounting surface, use suitable fittings.

Assembly

Note

The wall mounting must be capable of supporting at least four times the weight of the device.

To mount the device on a wall, follow the steps below:

1. Prepare the wall mounting with drilled holes and plugs. For the precise dimensions, refer to

the section "Dimension drawings (Page 67)".

2. Turn the upper screw in to the wall so that 10 mm remains jutting out.

3. Hang the device with the keyhole hanging mechanism on the rear on the screw.

4. Fix the device to the wall with the lower screw.

5. Connect the electrical connecting cables, refer to the section "Connecting up (Page 43)".

installing and removing

5.6 Wall mounting

SCALANCE XCM-300

Product

 Manual, 04/2022, C79000-G8976-C585-01

39

Summary of Contents for SIMATIC NET SCALANCE XCM-300



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands