Siemens SIMATIC NET S7-1200 Operating Instructions Manual Download Page 95

Page: 95 / 98

CP 1242-7
Operating Instructions, 09/2011, C79000-G8976-C247-02

Glossary

Communications module
Module for communications tasks that is used in an automation system as an interface

expansion of the CPU. Same interface types of a CPU and a CM are functionally identical.

CMT

Configuration and Monitoring Tool
Program user interface of TELECONTROL SERVER BASIC. Used for configuration of the

telecontrol server and monitoring of the connections to the remote stations.

Communications module

→

Communications processor

→

Communications processor
Module for expanded communications tasks that provides the CPU with additional interface

types or communications options.

GPRS

General Packet Radio Service
Packet-oriented service for IP-based data transmission in GSM networks. GPRS data

packets can also be transferred via the Internet. The data is transmitted using the Internet

protocols TCP/IP or UDP/IP.

GPRS direct (mode)

Mode of the CP 1242-7 for direct communication between remote S7 stations via the GSM

network. This mode is selected when it is known that the communications partner can be

reached using a fixed IP address. This is made possible by the services of the network

provider. No telecontrol server is necessary.

Summary of Contents for SIMATIC NET S7-1200



































































































Search results

Summary of Contents for SIMATIC NET S7-1200

Reviews:

Related manuals for SIMATIC NET S7-1200

Brands by name

Popular brands

Siemens SIMATIC NET S7-1200, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC NET S7-1200

Reviews:

Related manuals for SIMATIC NET S7-1200

Brands by name

Popular brands