Siemens SIMATIC NET RUGGEDCOM RSG2300 Installation Manual Download Page 53

Page: 53 / 54

Certification
6.2 EMC and Environmental Type Tests

temporary communication loss, while Class 2 requires error-free and interrupted

communications.

Description

Test Levels

Enclosure Contact

±2 kV
±8 kV

ESD

Enclosure Air

±15 kV

Radiated RFI

Enclosure Ports

35 V/m

Signal Ports

4 kV @ 2.5 kHz

DC Power Ports

4 kV

AC Power Ports

4 kV

Fast Transient

Earth Ground Ports

4 kV

Signal Ports

2.5 kV Common Mode @ 1 MHz

DC Power Ports

2.5 kV Common

1 kV differential mode @ 1 MHz

Oscillatory

AC Power Ports

2.5 kV Common

1 kV differential mode @ 1 MHz

Signal Ports

5 kV (Fail-Safe Relay Output)

DC Power Ports

5 kV

HV Impulse

AC Power Ports

5 kV

Signal Ports

2 kV

DC Power Ports

2 kV

Dielectric

Strength

AC Power Ports

2 kV

Damped

Oscillatory

Magnetic Field

Enclosure Ports

100 A/m

Environmental Type Tests

Test

Description

Test Levels

IEC 60068-2-1

Cold Temperature

Test Ad

-40 °C (-40 °F), 16 Hours

IEC 60068-2-2

Dry Heat

Test Bd

85 °C (185 °F), 16 Hours

IEC 60068-2-30

Humidity (Damp Heat, Cyclic)

Test Db

95% (Non-Condensing),

55 °C (131 °F), 6 Cycles

IEC 60068-2-6

IEC 60255-21-1

Vibration

2g @ 10-150 Hz, 2 hours per axis

IEC 60068-2-27
IEC 60255-21-2

Shock

30 g @ 11 ms

RUGGEDCOM RSG2300

Installation Manual, 04/2022, C79000-G8976-1046-18

Summary of Contents for SIMATIC NET RUGGEDCOM RSG2300























































Search results

Summary of Contents for SIMATIC NET RUGGEDCOM RSG2300

Reviews:

Related manuals for SIMATIC NET RUGGEDCOM RSG2300

Brands by name

Popular brands

Siemens SIMATIC NET RUGGEDCOM RSG2300, Installation Manual

Search results

Summary of Contents for SIMATIC NET RUGGEDCOM RSG2300

Reviews:

Related manuals for SIMATIC NET RUGGEDCOM RSG2300

Brands by name

Popular brands