Siemens SIMATIC NET RUGGEDCOM RS910W Installation Manual Download Page 43

Page: 43 / 52

Technical Specifications
5.7 Operating Environment

Copper Serial Ports

Baud Rate

300 to 230 kbps

Connector

DB9 or RJ45

Isolation

2.5 kV

Fiber Serial Ports

Mode

Multimode

Connector

Typical Distance (km)

Optical Wavelength

(nm)

820

Cable Size

50/125 or 62.5/125

5.7

Operating Environment

The RUGGEDCOM RS910W is rated to operate under the following environmental

conditions.

Ambient Operating

Temperature

-40 to 85 °C (-40 to 185 °F)

Ambient Storage Temperature

-40 to 85 °C (-40 to 185 °F)

Ambient Relative Humidity

5% to 95%

Maximum Altitude

2000 m (6562 ft)

Measured from a 30 cm (12 in) radius surrounding the center of the enclosure.

Non-condensing.

5.8

Mechanical Specifications

Weight

1.2 kg (2.7 lbs)

Ingress Protection

IP30

Enclosure

20 AWG Galvanized Steel

5.9

Dimension Drawings

Note

All dimensions are in millimeters, unless otherwise stated.

RUGGEDCOM RS910W

Installation Manual, 04/2021, C79000-G8976-1031-12

Summary of Contents for SIMATIC NET RUGGEDCOM RS910W





















































Search results

Summary of Contents for SIMATIC NET RUGGEDCOM RS910W

Reviews:

Related manuals for SIMATIC NET RUGGEDCOM RS910W

Brands by name

Popular brands

Siemens SIMATIC NET RUGGEDCOM RS910W, Installation Manual

Search results

Summary of Contents for SIMATIC NET RUGGEDCOM RS910W

Reviews:

Related manuals for SIMATIC NET RUGGEDCOM RS910W

Brands by name

Popular brands