manualshive.com logo in svg

Siemens SIMATIC NET RUGGEDCOM M2200F, Installation Manual

Share
Download
Siemens SIMATIC NET RUGGEDCOM M2200F Installation Manual Download Page 32

Communication Ports

4.2 Fiber Optic Ethernet Ports

Name

Pin

10/100Base-TX

1000Base-TX

Description

3

TX+

BI_DB+

Transmit Data+ or Bi-

Directional Pair B+

4

Reserved (Do Not Connect)

BI_DC+

Transmit Data+ or Bi-

Directional Pair C+

5

Reserved (Do Not Connect)

BI_DC-

Receive Data- or Bi-

Directional Pair C-

6

TX-

BI_DB-

Transmit Data- or Bi-

Directional Pair B-

7

Reserved (Do Not Connect)

BI_DD+

Receive Data- or Bi-

Directional Pair D+

8

Reserved (Do Not Connect)

BI_DD-

Receive Data- or Bi-

Directional Pair D-

Specifications

For specifications on the available copper Ethernet ports, refer to 

"Copper Ethernet

Port Specifications (Page 26)"

.

4.2

Fiber Optic Ethernet Ports

Fiber optic Ethernet ports are available with either LC (Lucent Connector), SC

(Standard or Subscriber Connector) or ST (Straight Tip) connectors. Make sure the

Transmit (Tx) and Receive (Rx) connections of each port are properly connected and

matched to establish a proper link.

2

1

     1    

Tx Connector

     2    

Rx Connector

Figure 4.4

SC Port

 

2

1

     1    

Tx Connector

     2    

Rx Connector

Figure 4.5

LC Port

2

1

     1    

Tx Connector

     2    

Rx Connector

Figure 4.6

ST Port

RUGGEDCOM M2200F

Installation Manual, 04/2022, C79000-G8976-1343-09

23

Summary of Contents for SIMATIC NET RUGGEDCOM M2200F

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands