Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO Manual Download Page 20

Page: 20 / 193

1 Technical Description, Installation Guidelines, Operation

IE/AS

−

INTERFACE LINK PN IO

as of hardware version 1, as of firmware version V2.0

Release 08/2018

C79000

−

G8976

−

C216

−

1.7

Connection Elements

Connectors

The IE/AS-i LINK has the following connectors:

Two separate connectors for the AS-i cable (on double master)

One connector for alternative power supply 24 V DC (optional) and functional

earthing

Two RJ-45 LAN connectors as independent switch ports

Power supply
connector 24 V DC

(alternative)

AS-i line 1
connector

(power supply from

AS-i line 1)

AS-i line 2
connector

(only with

double master)

LAN
connector 1

LAN
connector 2

Figure 1-3

Connectors for the AS-i Cable(s) and Power Supply

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO


































































































































































































Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands

Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO, Manual

Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands