Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO Manual Download Page 158

Page: 158 / 193

8 Using the Data Record Interface

158

IE/AS

−

INTERFACE LINK PN IO

as of hardware version 1, as of firmware version V2.0

Release 08/2018

C79000

−

G8976

−

C216

−

8.2.2.7

Read_Actual_Configuration

Meaning

This call reads the following configuration data (CDI) of an addressed AS-i slave
obtained by the AS-i master on the AS-Interface.

I/O configuration

ID code

ID1 code

ID2 code

The configuration data is specified by the manufacturer of the AS-i slave. The
meaning of the configuration data is described in /2/.

Structure of the RecordDataRead service − Index 11

Byte

Meaning

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Version_hi = 0x00

Version_lo = 0x00

I/O configuration

ID code

ID1 code

ID2 code

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO


































































































































































































Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands

Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO, Manual

Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Related manuals for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Brands by name

Popular brands