Siemens SIMATIC NET CP 343-1 Manual Download Page 16

Page: 16 / 78

Properties / services

1.5 The CP as Web server

CP 343-1

Manual, 12/2018, C79000

−G8976−C201

-08

Diagnostics buffer entries

When supplied, diagnostics buffer entries shown on diagnostics pages are always in English.

This is the case whichever language you have selected to display the Web pages.

How to download other language files to the CP and further information about Web

diagnostics can be found in the general Part A of this manual.

Web browser

To access the HTML pages on the CP, you require a Web browser. The following Web

browsers are suitable for communication with the CP (other browsers also possible):

●

Internet Explorer (recommended version: as of 7.0)

●

Chrome (recommended version: as of 12.0)

●

Opera (recommended version: as of 9.2)

●

Firefox (recommended version: as of 4.0)

You will find these Web browsers, information and any necessary add

ons on the Internet.

Summary of Contents for SIMATIC NET CP 343-1















































































Search results

Summary of Contents for SIMATIC NET CP 343-1

Reviews:

Related manuals for SIMATIC NET CP 343-1

Brands by name

Popular brands

Siemens SIMATIC NET CP 343-1, Manual

Search results

Summary of Contents for SIMATIC NET CP 343-1

Reviews:

Related manuals for SIMATIC NET CP 343-1

Brands by name

Popular brands