manualshive.com logo in svg

Siemens SIMATIC NET CP 243-1, Operating Instructions Manual, Page: 41 / 142

Share
Download
Siemens SIMATIC NET CP 243-1 Operating Instructions Manual Download Page 41

 

Application and properties 

 

1.12 Codes: Front LEDs 

CP 243-1 
Operating Instructions, 03/2012, C79000-G8976-C244-02 

41

 

 

 

 

RX/TX 

Green, flickering 

Ethernet activity: 
Data is being received or sent via 

Ethernet. 
Note: 

Frames not intended for the CP can 

also trigger LED activity. 

RUN 

Green, on continuously 

Ready for operation: 
The CP 243-1 is ready for 

communication 

CFG 

Yellow, on continuously 

Configuration: 
Lit when STEP 7 Micro/WIN 32 is 

actively maintaining a connection to the 

S7-200 CPU via the CP 243-1 

Function of the individual LEDs 

During the startup phase of the CP 243-1, the SF LED flashes twice. The LINK and the 

RX/TX LEDs then flash several times. As soon as the RUN LED is lit, the CP 243-1 startup 

has completed. 

Summary of Contents for SIMATIC NET CP 243-1















































































































































Reviews:

No comments