manualshive.com logo in svg

Siemens Simatic M7-400, Installation Manual

The Siemens Simatic M7-400 is a versatile industrial hardware device that revolutionizes automation processes. With its user-friendly interface, this product ensures seamless integration into any system. Enhance your understanding of its hardware and installation procedures with our comprehensive manual, available for free download on manualshive.com.

Share
Download
background image

Assembling and Installing Systems

A-13

S7-400 and M7-400 Programmable Controllers Hardware and Installation
A5E00069481-04

A.5

Shielding Cables

Purpose of the Shielding

A cable is shielded to attenuate the effects of magnetic, electrical, and
electromagnetic interference on this cable.

Principle of Operation

Interference currents on cable shields are discharged to ground via the shield bus
which is electrically connected to the housing. To prevent these interference
currents themselves from becoming an interference source, a low-impedance
connection to the protective ground conductor is particularly important.

Suitable Cables

If possible, only use cables with a braided shield. The coverage density of the
shield should be at least 80%. Avoid cables with a foil shield because the foil can
be easily damaged by tensile and compressive stress at the securing points; this
can reduce the shielding effect.

Grounding the Cable Shields

Generally, you should always connect both ends of the shield to the chassis ground
(that is, at the beginning and end of the cable). Grounding the shields at both ends
is essential to achieve a good degree of suppression of interference in the higher
frequency region.

In exceptional cases, you can connect only one end of the shield to the chassis
ground (for example, at the beginning or end of the cable). However, you only
achieve attenuation of lower frequencies. Single-ended connection of the shield
may be advantageous when

•

An equipotential bonding conductor cannot be laid

•

Analog signals of a few mA or 

m

A are transmitted

•

Foil shields (static shields) are used.

For data cables in serial communication, only use metallic or metallized
connectors. Secure the shield of the data cable to the connector housing. Do not
connect the shield to Pin 1 of the connector.

For stationary operation, you should strip the shielded cable without damaging the
shield and connect it to the shield/protective ground bar.

Note

In the event of potential differences between grounding points, a circulating current
may flow via the shield connected at both ends. In this case, install an additional
equipotential bonding conductor (see Section A.6).

Summary of Contents for Simatic M7-400





























































































































































































































































































































Reviews:

No comments

Related manuals for Simatic M7-400

Lauterbach C2000 Manual preview
C2000
Brand: Lauterbach Pages: 61
XMG OASIS Disassembly Procedure preview
OASIS
Brand: XMG Pages: 5
NAD M10 Quick Setup Manual preview
M10
Brand: NAD Pages: 2
Cabletron Systems Netlink FRX8000 Installation And Setup Manual preview
Netlink FRX8000
Brand: Cabletron Systems Pages: 94
Cabletron Systems MMAC-Plus 9E423-24 Reference Manual preview
MMAC-Plus 9E423-24
Brand: Cabletron Systems Pages: 10
Cabletron Systems MMAC-Plus 9A128-01 Management Manual preview
MMAC-Plus 9A128-01
Brand: Cabletron Systems Pages: 22
Cabletron Systems Spectrum EMM-E6 Addendum Manual preview
Spectrum EMM-E6
Brand: Cabletron Systems Pages: 2
Cabletron Systems DLM6C-AA Overview And Setup Manual preview
DLM6C-AA
Brand: Cabletron Systems Pages: 54
Cabletron Systems Cabletron BRIM-F6 User Manual preview
Cabletron BRIM-F6
Brand: Cabletron Systems Pages: 43
Cabletron Systems Netlink FRX4000 Maintenance Manual preview
Netlink FRX4000
Brand: Cabletron Systems Pages: 60
Cabletron Systems 9E132-15 Appendix preview
9E132-15
Brand: Cabletron Systems Pages: 8
Cabletron Systems TRXI-22 Addendum preview
TRXI-22
Brand: Cabletron Systems Pages: 4
Phytec L-843e.A1 Hardware Manual preview
L-843e.A1
Brand: Phytec Pages: 53
ZyXEL Communications EOC350 Series Quick Start Manual preview
EOC350 Series
Brand: ZyXEL Communications Pages: 2
Dahua NVS0X04DH Quick Start Manual preview
NVS0X04DH
Brand: Dahua Pages: 24
LSI MegaRAID SATA 300-4XLP Quick Installation Manual preview
MegaRAID SATA 300-4XLP
Brand: LSI Pages: 3
LevelOne FPC-0103T Manual preview
FPC-0103T
Brand: LevelOne Pages: 31
Fracarro FRPRO EVO HD Quick Start Manual preview
FRPRO EVO HD
Brand: Fracarro Pages: 12

Brands by name

Popular brands

Load more brands