Siemens SIMATIC IPC627E Operating Instructions Manual Download

Page: 17 / 164

Product description

1.4 External design of the device

SIMATIC IPC627E
Operating Instructions, 12/2018, A5E44297201-AA

⑧

2 × USB

X60/X62

USB 3.1 Gen. 2 Type A high current, backward compatible with USB 3.0/2.0/1.1

⑨

2 × USB

X64/X65

USB 3.1 Gen. 2 Type A high current, backward compatible with USB 3.0/2.0/1.1

⑩

100-240 V AC

Power supply connection

⑪

On/off switch

You switch on the device with the on/off switch. This requires that the BIOS setup entry

"State After G3" is set to "S0 State (=Always On)".
The on/off switch does not isolate the device from the power supply. Position "ON", when

the "-)" symbol is pressed inward on the device. Position "OFF" is the delivery state.

⑫

PCI/PCIe expansion

cards,
USB on expansion

card (optional)

2 slots for expansion cards (Slot1/X101, Slot2/X102)

⑬

Fixing screws for strain

relief

Summary of Contents for SIMATIC IPC627E





































































































































































Search results

Summary of Contents for SIMATIC IPC627E

Reviews:

Related manuals for SIMATIC IPC627E

Brands by name

Popular brands

Siemens SIMATIC IPC627E, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IPC627E

Reviews:

Related manuals for SIMATIC IPC627E

Brands by name

Popular brands