Siemens SIMATIC IPC1047 Operating Instructions Manual Download Page 56

Page: 56 / 136

Expanding and assigning parameters to the device

6.4 Drives

SIMATIC IPC1047

Operating Instructions, 09/2018, A5E45118479-AA

6.4.2

Removing and installing a tray from/in the drive cage

Requirement

●

The device is open; see section "Open the device. (Page 52)".

●

1 soft, grounded mounting base

Procedure

Read section "ESD guideline (Page 103)".

Removal

1. Detach the marked connection

cables from the relevant drive.

2. Press the side rails of the tray

inwardly and simultaneously lift

them up and out of the drive

cage.

3. Place the tray on the mounting

base.

Installation
Proceed in the reverse order for the installation. Ensure that the tray latches in the bottom of

the drive cage.

6.4.3

Removing and installing 3.5" drives from/in tray

Requirement

●

The tray has been removed, see section

"Removing and installing a tray from/in the drive cage (Page 56)".

●

1 drive

●

1 soft mounting base

Summary of Contents for SIMATIC IPC1047









































































































































Search results

Summary of Contents for SIMATIC IPC1047

Reviews:

Siemens SIMATIC IPC1047, Operating Instructions Manual, Page: 56 / 136

Search results

Summary of Contents for SIMATIC IPC1047

Reviews: