manualshive.com logo in svg

Siemens SIMATIC HMI TP1000F Mobile RO, Operating Instructions Manual, Page: 176 / 196

Share
Download
Siemens SIMATIC HMI TP1000F Mobile RO Operating Instructions Manual Download Page 176

Technical specifications 

 

9.9 Connection box compact interfaces 

 

TP1000F Mobile RO 

176

 

Operating Instructions, 08/2017, A5E39831415-AA  

9.9.3

 

Plug-in terminal strip X10 

Plug-in terminal strip, 12-pin 

 

Contact 

Assignment 

Associated circuits and reference information 

1 

Functional grounding  Ground and power supply 

See "Connecting the functional grounding and power supply 

to the connection box (Page 55)." 

2 

M 

3 

P24 

4 

Not connected 

5 

ENABLE2– 

Enabling button 
See section "Operating the enabling button (Page 67)" and 

wiring information in the following section 

6 

 

7 

ENABLE1– 

8 

 

9 

STOP 24 

Emergency stop / stop button 
See section "Pressing the emergency stop / stop button 

(Page 68)" and wiring information in the following section 

10 

STOP 23 

11 

STOP 14 

12 

STOP 13 

9.9.4

 

Wiring of safety-related operator controls 

Emergency stop/stop button 

The figure below shows the wiring of the emergency stop/stop button in the connection box 

compact. 

 

Summary of Contents for SIMATIC HMI TP1000F Mobile RO





































































































































































































Reviews:

No comments