manualshive.com logo in svg

Siemens SIMATIC HMI TP1000F Mobile RO, Operating Instructions Manual, Page: 55 / 196

Share
Download
Siemens SIMATIC HMI TP1000F Mobile RO Operating Instructions Manual Download Page 55

 

Installing system components 

 

3.6 Connecting the connection box 

TP1000F Mobile RO 
Operating Instructions, 08/2017, A5E39831415-AA  

55

 

3.6.4

 

Connecting the functional grounding and power supply to the connection box 

The power supply for the HMI device is connected to a terminal strip in the connection box. 

The connection box has reverse polarity protection. 

 

 

WARNING 

24 V DC power supply 
If the supply voltage is outside the specified range, it may cause the HMI device to 

malfunction. This can result in personal injury or material damage. 
Use a 24 V DC power supply with the following properties for the connection box: 

•

 

Safe electrical isolation according to IEC 60364-4-41 or HD 384.04.41 (VDE 0100, 

Part 410). 

•

 

The power supply provides safety extra-low voltage according to SELV/PELV up to a 

maximum of 36 V DC and also does not exceed 

m

 = 36 V DC in case of fault. Refer to 

the information in the data sheet for overvoltage protection in the event of an internal 

error or take appropriate voltage-limiting measures, such as the use of a surge 

protection device. 

 

 

NOTICE 
External protective circuit  
An external protective circuit is required for operation with 24 V DC; please refer to 

section 7 "Lightning protection and overvoltage protection" in the following function manual: 

"Designing interference-free SIMATIC S7-1500, ET 200MP, ET 200SP, ET 200AL 

controllers (

https://support.industry.siemens.com/cs/ww/en/view/59193566

)". 

 

Requirement 

●

 

The power supply meets the requirements set out in "Technical specifications 

(Page 165)". 

●

 

The connection box standard or advanced is open. 

●

 

The power cable wires have been stripped by 6 mm. 

●

 

Power supply cables and equipotential bonding conductor, cross-section 1.5 mm

2

 

●

 

Wire end ferrules ∅ 0.5 mm.

 

Procedure  

1.

 

For connection box standard and connection box advanced 
Thread the cables through the corresponding screw glands. 

2.

 

Place a wire end ferrule on each wire to be connected. 

Summary of Contents for SIMATIC HMI TP1000F Mobile RO





































































































































































































Reviews:

No comments