Siemens Simatic ET200pro Operating Instructions Manual Download Page 247

Page: 247 / 545

General technical data

10.5 Specifications for insulation tests, protection class, degree of protection, and rated voltage

ET 200pro distributed I/O system
Operating Instructions, 03/2013, A5E00335544-08

247

10.5

Specifications for insulation tests, protection class, degree of

protection, and rated voltage

Test voltage

The proof of dielectric strength is provided in a type test with the following test voltage

according to IEC 61131-2:

Circuits with rated voltage V

against other circuits or ground.

Test voltage

< 50 V

500 V DC

< 150 V

2500 V DC

< 250 V

4000 V DC

Pollution degree/overvoltage category according to IEC 61131-2

●

Pollution degree 2

●

Overvoltage category
–

At V

= 24 V DC: II

Degree of protection IP65

Degree of protection according to IEC 60529

●

Protection against the ingress of dust and full touch protection

●

Water projected by a nozzle against the enclosure from any direction shall have no

harmful effect.

Degrees of protection IP66 and IP67

Degree of protection according to IEC 60529

●

Protection against the ingress of dust and full touch protection

●

IP66: Water from heavy seas or water projected in powerful jets shall not enter the

enclosure in harmful quantities.

●

IP67: Protection against water when enclosure is immersed at specified pressures over a

specified time period (water must not enter the enclosure in any harmful amount)

Rated voltage for operation

The ET 200pro distributed I/O system operates at the following rated voltage and

corresponding tolerance.

Rated voltage

Tolerance range

24 V DC

20.4 V DC to 28.8 V DC

Summary of Contents for Simatic ET200pro


































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands

Siemens Simatic ET200pro, Operating Instructions Manual

Search results

Summary of Contents for Simatic ET200pro

Reviews:

Related manuals for Simatic ET200pro

Brands by name

Popular brands