manualshive.com logo in svg

Siemens SIMATIC ET 200SP CM 1xDALI, Manual, Page: 80 / 126

Share
Download
Siemens SIMATIC ET 200SP CM 1xDALI Manual Download Page 80

 

Programming 

 

5.7 Configuration function blocks 

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0) 
Manual, 06/2019, A5E46959434-AA 

79

 

5.7.6

 

DALI_ECG_SET_EXT_PARAM 

Description 

DALI_ECG_SET_EXT_PARAM is used for setting the extended parameters of DALI control 

gears. The extended parameters are type-related.  

●

 

If the status of control gear is configured (for example, control gear is added by using 

DALI_ECG_ADD (Page 67)), the parameters are saved in the CM 1xDALI (refer to data 

flow path 1 (Page 23)) and sent to the physical device (refer to data flow path 5 

(Page 23)). 

●

 

If the status of control gear is not configured, the parameters are only sent to the physical 

device (refer to data flow path 5 (Page 23)). 

●

 

This function block does not check whether the input parameter EXT_PRM_SET is valid 

for the specified control gear. 

You can query the extended parameters of control gear by using 

DALI_ECG_QUERY_EXT_PARAM (Page 75). 

Summary of Contents for SIMATIC ET 200SP CM 1xDALI































































































































Reviews:

No comments