manualshive.com logo in svg

Siemens SIMATIC ET 200SP CM 1xDALI, Manual, Page: 76 / 126

Share
Download
Siemens SIMATIC ET 200SP CM 1xDALI Manual Download Page 76

 

Programming 

 

5.7 Configuration function blocks 

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0) 
Manual, 06/2019, A5E46959434-AA 

75

 

5.7.5

 

DALI_ECG_QUERY_EXT_PARAM 

Description 

DALI_ECG_QUERY_EXT_PARAM is used for querying the extended parameters of DALI 

control gears.  

●

 

When you set the input "PHY_DEV" to 1, this function block queries the extended 

parameters from the physical device (refer to data flow path 6 (Page 23)). 

●

 

When you set the input "PHY_DEV" to 0, this function block queries the parameters which 

are saved in CM 1xDALI (refer to data flow path 2 (Page 23)). 

The extended parameters have the following features: 

●

 

The extended parameters are type-related. 

●

 

The extended parameters in the physical device can only be queried from the control 

gears whose type range is from 1 to 8; Otherwise, the error code “16#87” (Not supported) 

is shown in the output parameter of STATUS. 

●

 

The extended parameters which are saved in CM 1xDALI can only be queried from the 

control gear whose type is 1, or 4 to 8. 

You can set the extended parameters of control gear by using 

DALI_ECG_SET_EXT_PARAM (Page 79). 

Summary of Contents for SIMATIC ET 200SP CM 1xDALI































































































































Reviews:

No comments