Siemens SIMATIC EM 300 Manual Download Page 37 | Manualshive

Page: 37 / 74

background image

Commissioning

SIMATIC - EM 300 Motor Starters
GWA-4NEB 640070302-05

3-9

Local reset

If you press the TEST/RESET button during a local reset, various responses are
triggered depending on how long the button is depressed (see the following
table).

Reset after signal "FAULT/release signal" (DI2)

After a release signal (device continues operation) resp. overload release (device
is shut down) the OVERLOAD LED lights up. After a FAULT signal (device is shut
down) the FAULT LED lights up. You can reset the OVERLOAD resp. the FAULT
display and the DI2 signal with a local or remote reset in which case the LEDs
goes out.

Communication failure

If communication fails, the circuit outputs are reset after approx. 100 ms.
Restart is automatic.

Note

If the 24 V DC supply voltage for electronic motor starters is interrupted for lon-
ger than 5 seconds, a waiting period of t > 50 s for normal operation must be
observed before switching back on.

Rotary

encoder

switch

setting

Reset

Procedure

Tripping

REMOTE

Local reset

•

Press the RESET/RESET button for less than 2 s:

– A pending FAULT signal is reset if the cause of the fault has

been remedied.

•

Press the TEST/RESET button for more than 2 s:

– Fast discharge of the motor model, i. e. the motor model is

reset without a delay,

– Device self-test is triggered. Press the TEST/RESET button

again as soon as the READY LED lights up again.

Auto reset

The release signal is reset automatically as soon as the motor model is
below the release threshhold again.

Tripping

LOCAL

Local reset

•

Press the RESET/RESET button for less than 2 s:

– The release signal is reset as soon as the motor model is below

the release threshhold again,

– A pending FAULT signal is reset if the cause of the fault has

been remedied.

•

Press the TEST/RESET button for more than 2 s:

– Fast discharge of the motor model, i. e. the motor model is

reset without a delay,

– Device self-test is triggered. Press the TEST/RESET button

again as soon as the READY LED lights up again.

Remote

Reset

In the user program set output DO3 to "1" and then to "0" again.

«
...
35
36
37
38
39
...
»

Summary of Contents for SIMATIC EM 300











































































Reviews:

No comments

Related manuals for SIMATIC EM 300

Brand: Zolix Instruments Pages: 22

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 168

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 29

Brand: Panasonic Pages: 37

Brand: Panasonic Pages: 9

Brand: Abus Pages: 12

Brand: Gardena Pages: 17

Brand: SAFI Pages: 18

Brand: Badger Meter Pages: 2

Brand: Badger Meter Pages: 48

BadgerTouch HREBT

Brand: Badger Meter Pages: 12

Brand: Badger Meter Pages: 16

Brand: CAME Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands