manualshive.com logo in svg

Siemens SIMATIC CPU 1515SP PC2 F, User Manual

Share
Download
Siemens SIMATIC CPU 1515SP PC2 F User Manual Download Page 44

 

Commissioning 

 

8.2 Basic commissioning procedure 

CPU 1515SP PC2 (F/T/TF) 
Operating Instructions, 09/2018, A5E42603425-AA 

43

 

8.2

 

Basic commissioning procedure 

 

Step 

Execution 

Section 

1 

Requirements 

8.2.1 (Page 43) 

2 

Preparing commissioning 

8.2.2 (Page 43) 

3 

Commissioning procedure 

8.2.3 (Page 43) 

8.2.1

 

Requirements 

The following requirements must be met before you commission the Open Controller for the 

first time: 

●

 

The CPU 1515SP PC2 is mounted. 

●

 

The supplied CFast card is inserted. 

●

 

No data carriers are connected via USB. 

8.2.2

 

Preparing commissioning 

Procedure  

When the requirements are met, proceed as follows with the commissioning: 
1.

 

Connect a monitor using a DisplayPort cable. 

2.

 

Connect a keyboard and a mouse to the CPU via USB. 

Result 

The Open Controller is prepared for commissioning. 
 

8.2.3

 

Commissioning procedure 

When you start up your CPU 1515SP PC2 for the first time, basic settings and the 

administrator password are queried. The device is then automatically set up for the operating 

system that is installed on the CFast card. Restart the device after the operating system has 

been set up.  

 

 

Note 
The initial commissioning is not possible with a Multitouch panel, as the Multitouch driver is 

only available after the installation of the operating system. 

 

Summary of Contents for SIMATIC CPU 1515SP PC2 F









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands