manualshive.com logo in svg

Siemens SIMATIC 6ES7 972-0CB20-0XA0, Manual

Share
Download
Siemens SIMATIC 6ES7 972-0CB20-0XA0 Manual Download Page 16

Hardware Design of the PC Adapter USB

PC Adapter USB

4-2

A5E00166353-02

4.2 

LEDs on the PC Adapter USB

The LEDs on the PC Adapter USB indicate the following:

 

Name

 

Color

 

Meaning

USB

green

Lights when the PC Adapter USB is connected to the USB and
the operating system of your PC is in the normal operating
mode. This LED is not lit when the PC is in standby or idle
mode.

The LED flashes during data transmission.

POWER

green

Lights when the PC Adapter USB is supplied with the
necessary power.

Flashes when a hardware fault is detected.

MPI

green

Lights when the PC Adapter USB is connected to the MPI/DP
network and is operational.

The LED flashes during active data transmission via the
MPI/DP network.

The LED is off when no firmware has been loaded in the PC
Adapter USB.

The LED displays for error states are described in Chapter 8: Error Diagnostics.

13.05.2003

3.05.2003

13.05.2003

13.05.2003

Summary of Contents for SIMATIC 6ES7 972-0CB20-0XA0







































Reviews:

No comments

Brands by name

Popular brands

Load more brands