background image

2.4

Measures

In the interest of safety, observe the following precautionary measures: 

WARNING

Type of protection with electrical devices for Zone 2 "nA"
Devices with the type of protection "Non incendive equipment nA" may only be opened when 

off circuit.

WARNING

Use in environments with aggressive and dangerous media
The device can be operated both at high pressure and with aggressive and hazardous media. 

Therefore, improper use of this device may lead to serious injury and or considerable damage 

to property. Above all, it must be noted when the device was in use and is to be exchanged.

CAUTION

Electrostatic sensitive devices
This device contains electrostatic sensitive devices. ESD devices can be destroyed by 

voltages well below the threshold of human perception. These static voltages develop when 

you touch a component or electrical connection of a device without having discharged the 

static charges present on your body. The damage to a module as a result of overvoltage 

cannot usually be detected immediately. It may only become apparent after a long period of 

operation.

Safety instructions
2.4 Measures

Distributed I/O 6DL2804-3xxxx & 6DL2804-4xxxx

8

Hardware Installation Manual, 04/2017, A5E41591350-AA

Summary of Contents for SIMATIC 6DL2804-3 Series













































Reviews: