Siemens SIMATIC 6AV7861-1AA00-0AA0 Operating Instructions Manual Download | Manualshive

Page: 13 / 26

background image

Unpack and connect the device

2.6 Connecting the Cables

Flat Panel
Operating Instructions (Compact), 09/2008, A5E02313712-01

13

Procedure when the distance is > 5 m (extended and PRO version)

Figure 2-5

Cable connection

(1)  Long connecting cable
(2)  USB link on the control unit
(3)  Operating unit
(4)  USB-connection on the USB transmitter module
(5)  USB-transmitter module
(6)  Short connecting cable

1.

Plug the female connector of the long USB connecting cable (1) into the port (2)

(USB link) on the control unit (3).

2.

Plug the USB connecting cable (1) into the port (4) () on the USB transmitter module (5).
The control unit is connected to the USB transmitter module.

3.

Use the second, short USB connecting cable (6) to connect the USB transmitter module

to the computer unit.

4.

Connect the DVI cable to the Flat Panel and the computer unit.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

«
...
11
12
13
14
15
...
»

Summary of Contents for SIMATIC 6AV7861-1AA00-0AA0



























Reviews:

No comments

Related manuals for SIMATIC 6AV7861-1AA00-0AA0

Brand: Rath Pages: 3

Brand: Eclipse Combustion Pages: 46

Brand: Bard Pages: 2

Brand: Keiser Pages: 2

Brand: ECA Pages: 3

Brand: Nautilus Pages: 12

Brand: FJC Pages: 2

Brand: JB-Lighting Pages: 40

Brand: E-Z DRILL Pages: 12

Brand: e-survey Pages: 54

Brand: E-Pill Pages: 8

XL-7 Command Station

Brand: E-Mu Pages: 22

Brand: Ransomes Pages: 282

Ransomes HR 6010

Brand: Jacobsen Pages: 10

Brand: LA Audio Pages: 9

Brand: UEi Pages: 5

Brand: UGO BASILE Pages: 47

Brand: UFO Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands