manualshive.com logo in svg

Siemens SICAM Q80, System Manual, Page: 23 / 240

Share
Download
Siemens SICAM Q80 System Manual Download Page 23

 23

Operation modes and settings

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

active

.

 

Load last parameter set + edit (offline)

: Loads the last edited parameter set. Here, no connection to the

device is established. The configuration can be changed while the measurement device is performing a
measurement. Only available while the device is 

active

.

Load last parameter set + connect (+stop)

: Loads the last edited parameter set. Subsequently, the software

goes to the 

Start/Stop

 page and establishes a connection with the device. The running measurement is

automatically stopped. Only available while the device is 

active

.

Apply topology data

: Applies the device assignment from the topology. This is necessary if the topology

assignment was changed. In the program's title bar, the new assignment is displayed. Only available while the
device is 

active

.

Connection with  import parameter set (online)

: The system goes to the 

Start/Stop page

. The

current parameters are imported  from the device. This involves only a simple connection with the device in
order to import the parameters. Online values are not displayed as part of this action. For that purpose, the 

Connect-command

 must be called! Only available while the device is 

active

.

 Load parameter set...

: The dialog for selecting an arbitrary parameter set is displayed. The files are in the

format *.nqa, see also 

here

. Only available while the device is 

active

.

Save

: Saves the current parameter set. Only available while the device is 

active

.

Save as...

: Saves the current settings under a new name for the parameter set. Only available while the device

is 

active

.

Load template...

: Loads a template by means of the selection dialog which appears. Only available while the

device is 

active

.

Save as template...

: Saves the current settings as a general template. A template amounts to a parameter set

without any fixed assignment to a device. Only available while the device is 

active

.

Status of the measurement

 Get measurement status

: The system queries the current measurement status for frequency and voltage

U1. When the interface to the device is slow, only the frequency is queried. Only available while the device is 

active

.

 Acknowledge status:

: The entry returned by 

Get measurement  status 

is deleted.

Extras: 

 

Set as passive

: The device is not used in this topology, see also 

here.

 

Activate

: The device is used in this topology. Activation is also necessary so that other menu entries are

operable, see also 

here.

 

Conclude measurement data

: Closes the current measured data in the device and makes them ready to be

retrieved, see also 

here.

 

Stop measurement

: Stops the running measurement.

Update firmware...

: Starts a firmware update. For this purpose, the running measurement is concluded. The

Autostart configuration is also deleted in the process, and is only generated again upon starting the new
measurement.

General

 

Delete:

 The selected entry (entries) and all associated sub-entries are deleted.

 

Properties

: The properties of the selected topology entry, see 

here

Property

Following 

querying of the measurement state

, the measurement device's properties are listed. This will include

the current IP-address as well as the time at which this address was determined. This allows you, among other
things, to check which address the device received via DHCP.

 

23

23

63

23

23

63

65

23

20

23

23

23

23

23

23

24

24

24

26

21

Summary of Contents for SICAM Q80

















































































































































































































































Reviews:

No comments