Siemens SICAM Q80 System Manual Download Page 147

Page: 147 / 240

147

Operation modes and settings

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

Call to the AutoTransfer log file

Open the log file with any text editor.

Log file of Auto-Transfer

Note

Log-files are saved to the default service path, which can not be changed. This includes the
following log files:

SICAM Q80 Manager - main log

Autoreport- general

5.1.7.1.1 Comfortable configuration step-by-step

Configure SICAM Q80 Manager

devices at

„Events“

with active UDP-signal.

2. Autotransfer: Define a "default device" under

Settings\Default

Status

active

Transfer Option

to "

UDP

Autotransfer"

3. In the

UDP settings properties

under

Settings\General

assign a port and set to active.

i. Set the port number as previously under item (1).

ii. Activate the default assignment and select your default device (2).

All measurement devices which were configured for sending UDP are then automatically recognized and perform the
default device's options. If there are new devices, the program Auto-Transfer does not need to be configured.

145

144

Summary of Contents for SICAM Q80

















































































































































































































































Siemens SICAM Q80, System Manual, Page: 147 / 240

Search results

Summary of Contents for SICAM Q80

Reviews: