manualshive.com logo in svg

Siemens SENTRON PAC2200CLP, Product Manual, Page: 75 / 130

Share
Download
Siemens SENTRON PAC2200CLP Product Manual Download Page 75

 

PAC2200CLP 
Equipment Manual, 06/2021, L1V30820585B-02 

73

 

  Service and maintenance

 

7 

 

 

The device requires no maintenance. 

7.1

 

Cleaning 

Clean the device as required. Use a dry cloth for this. 

 

 

NOTICE 
Damage may result from use of detergents. 

Detergents can damage the device. Do not use detergents. 

 

7.2

 

Calibration 

The device has been calibrated by the manufacturer before shipping. Recalibration is not 

required provided the environmental conditions are maintained. 

7.3

 

Troubleshooting guide 

Remedies for the resolution of faults 

 

Fault 

Remedies 

Device is not working 

•

 

Check power supply 

•

 

Check fuse 

Voltage or current measured values are not displayed 

•

 

Check fuse 

•

 

Check the configuration (see Parameterizing the device 

(Page 60)) 

Voltage values are not plausible 

•

 

Check the voltage taps at the different phases to deter-

mine whether or not voltage is present 

Current values are not plausible 

•

 

Check the settings and the wiring of the current trans-

former (if present) and correct if necessary 

Summary of Contents for SENTRON PAC2200CLP



































































































































Reviews:

No comments