manualshive.com logo in svg

Siemens SENTRON 7KT PAC1600 Series, Manual, Page: 17 / 76

Share
Download
Siemens SENTRON 7KT PAC1600 Series Manual Download Page 17

 

Description 

 

3.3 7KT PAC1600 multimeter 

7KT multimeter 
Manual, 08/2018, 2514284149-01 

15

 

Measuring input voltages 

The device is designed for the following measuring input voltages: 

●

 

For measuring input voltages up to 415 V phase-to-neutral 

●

 

For measuring input voltages up to 720 V phase-to-phase 

3.3

 

7KT PAC1600 multimeter 

 

①

 

Sealing cover 

②

 

Display 

③

 

Arrow key for scrolling, selecting 

and changing 

 

④

 

Arrow key for scrolling, selecting 

and changing 

You will find information on operation in chapter Keypad functions 

(Page 16) ff. 

⑤

 

Arrow key for scrolling, confirming 

and switching over 

 

⑥

 

Menu key 

 

Basic properties 

●

 

Three-phase digital multimeter 

●

 

4U modular enclosure (72 mm) for DIN rail 

●

 

Backlit LCD 

●

 

2 versions: 
–

 

7KT1681: Standard version 

–

 

7KT1682: With built-in RS 485 interface 

●

 

4 navigation keys for functions and settings 

●

 

Extremely accurate measurement of demand (TRMS) 

●

 

Wide selection of available measurements, including voltage, current, THD and 

harmonics analysis 

Summary of Contents for SENTRON 7KT PAC1600 Series













































































Reviews:

No comments