Siemens SENTRON 7KT PAC1600 Series Manual Download Page 18

Page: 18 / 76

Description

3.3 7KT PAC1600 multimeter

7KT multimeter

Manual, 08/2018, 2514284149-01

●

Wide-range auxiliary power supply unit (100 V AC … 240 V AC)

●

Two-level password protection for settings

●

Backup copy of original settings

●

Texts available in six languages

Display indications

①

Measured variable display

②

Selected phase

③

Subpage: Measurement type

④

Communication active

⑤

Alarm icon

⑥

End-of-scale value

⑦

Bar diagram

⑧

Unit of measured variables

3.3.1

Keypad functions

Menu key

The Menu key is used for opening and closing the display and setup menus.

Arrow keys , and

Arrow keys and are used for

●

Scrolling between screens

●

Selecting available options on the display

●

Changing (increasing/decreasing) settings

The arrow key is used for

●

Scrolling to subpages

●

Confirming selected options

●

Switching between display modes

Summary of Contents for SENTRON 7KT PAC1600 Series













































































Search results

Summary of Contents for SENTRON 7KT PAC1600 Series

Reviews:

Siemens SENTRON 7KT PAC1600 Series, Manual, Page: 18 / 76

Search results

Summary of Contents for SENTRON 7KT PAC1600 Series

Reviews: