Siemens SENTRON 3WA System Manual Download | Manualshive

Page: 37 / 82

background image

3WA Air Circuit Breaker Communication
System Manual, 11/2021, 92310000004-02

35

Modbus TCP

5

5.1

General

The COM190 communication module supports the Modbus TCP protocol of the Modbus

Organization, described in the following specifications:

•

Modbus Application Protocol V1.1b3

•

Modbus Messaging Implementation Guide V1.0b

You can find more information on the Internet (

).

5.2

Addressing

With Modbus TCP, the COM190 module is addressed via its IP address.
The COM190 has a data point that contains the communication parameters for access via

TCP/IP (IPv4 suite).

Read and write access

Read access to the data point takes place as follows:

•

For the COM190 with role A, via Modbus register number 42009 (hex: 0xA419)

•

For the COM190 with role B, via Modbus register number 43009 (hex: 0xA801)

Write access to the IPv4 suite takes place via a command with Modbus function code 16

(hex: 0x10):

•

For the COM190 with role A, via Modbus register number 42900 (hex: 0xA794)

•

For the COM190 with role B, via Modbus register number 43900 (hex: 0xAB7C)

Modbus TCP port

The default TCP port for a Modbus TCP server is 502. The COM190 module has a data point

"Modbus TCP port" that is configured as 502 in the as-delivered state.
It is possible to change this value. You can find more information in Chapter Configurable

Modbus TCP port (Page 43).

«
...
35
36
37
38
39
...
»

Summary of Contents for SENTRON 3WA



















































































Reviews:

No comments

Related manuals for SENTRON 3WA

SureTest 61-164

Brand: IDEAL Pages: 24

Brand: Eaton Pages: 34

Brand: ABB Pages: 5

Brand: Eaton Pages: 207

Brand: Elenco Electronics Pages: 12

Spectra K-frame

Brand: GE Pages: 4

DUSPOL digital LC

Brand: Benning Pages: 67

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands